Thermal Analysis Simulation for Laser Butt Welding of Inconel625 Using FEA

@article{Vemanaboina2018ThermalAS,
  title={Thermal Analysis Simulation for Laser Butt Welding of Inconel625 Using FEA},
  author={Harinadh Vemanaboina and Gundabattini Edison and Suresh Akella and Ramesh Kumar Buddu},
  journal={International Journal of Engineering \& Technology},
  year={2018}
}
Laser welding process is employed in the manufacturing of critical components where the final assembly units necessitate strict tolerances like low distortions and residual stresses. Laser beam welding offers several advantages like low heat input, very narrow heat affected zone, low residual stresses, low distortions and good mechanical joint properties in the weld joints when compared to the conventional techniques like Tungsten Inert Gas Arc welding processes. However, the implementation of… Expand
6 Citations

Figures from this paper

Numerical simulation of temperature distribution and experimentation in laser beam welding of SS317L alloy
Abstract In the present study stainless steel 317L grade was chosen for joining using 400w Nd-YAG laser beam welding process. Tensile strength and temperature distribution are considered as outputExpand
Mechanical and Metallurgical Properties of CO2 Laser Beam INCONEL 625 Welded Joints
In the frame of the circular economy, welding of Ni-based superalloys has gained increasing importance when applied, for instance, to repairing highly expensive components widely used in strategicalExpand
Thermal and Residual Stress Distributions in Inconel 625 Butt-Welded Plates: Simulation and Experimental Validation
Thermal and residual stress distributions induced by the gas tungsten arc welding (GTAW) process on Inconel 625 were studied using numerical simulation and experiments. A multi-pass welding model wasExpand
Residual stress analysis, mechanical and metallurgical properties of dissimilar weldments of Monel 400 and AISI 316
Abstract This research manuscript explores the residual stress analysis, mechanical and metallurgical aspects of dissimilar welded joints between AISI 316 and Monel 400 developed by constant, pulseExpand

References

SHOWING 1-10 OF 12 REFERENCES
A Welding Simulation of Dissimilar Materials SS304 and Copper
A welding simulation is developed for dissimilar metals followed by a mathematical model for laser beam welding. In this work a Finite element model for dissimilar welding of 304 steel & Copper isExpand
Numerical simulation of residual stresses induced by laser beam welding in a SUS316 stainless steel pipe with considering initial residual stress influences
With the development of computer hardware and software, numerical simulation technology has been widely used to predict welding temperature field, residual stresses and distortion. However, till nowExpand
Welding Process Simulation Model for Temperature and Residual Stress Analysis
Abstract Welding is widely used in all the fabrication processes for the development of structural components. An accurate and physically suitable heat flux simulation model is to be given as inputExpand
The effect of thermal properties and weld efficiency on residual stresses in welding
AbstrAct Purpose: A parametric model is adopted and the technique of element “birth and death” is used to estimate the effect of thermal properties and weld efficiency on residual stresses in buttExpand
Finite element simulation of laser spot welding
Abstract The present work reports on a two-dimensional axisymmetric finite element analysis of heat flow during laser spot welding, taking into account the temperature dependence of the physicalExpand
Applications of inherent strain and interface element to simulation of welding deformation in thin plate structures
Welding-induced distortion not only reduces largely manufacturing accuracy but also decreases significantly productivity due to correction works. If welding distortion can be predicted through aExpand
STUDY OF THE GAUSSIAN DISTRIBUTION HEAT SOURCE MODEL APPLIED TO NUMERICAL THERMAL SIMULATIONS OF TIG WELDING PROCESSES
Welding processes are considered a thermal-mechanical-metallurgical coupled issue. The most important boundary condition in the numerical thermal analysis is the heat source model. Although manyExpand
3D finite element simulation of temperature distribution, residual stress and distortion on 304 stainless steel plates using GTA welding
In the present study, the distortion induced in rectangular plate of AISI 304 SS during autogenous GTA welding process is measured experimentally and further validated using Finite element (FE)Expand
Numerical simulation of laser full penetration welding
A three dimensional finite element model has been developed to dynamically simulate the laser full penetration welding process. The parametric design capabilities of the finite element code ANSYSExpand
Computational Welding Mechanics
...
1
2
...