The influence of luting systems on the microtensile bond strength of dentin to indirect resin-based composite and ceramic restorations.

@article{DArcangelo2009TheIO,
  title={The influence of luting systems on the microtensile bond strength of dentin to indirect resin-based composite and ceramic restorations.},
  author={Camillo D'Arcangelo and Francesco de Angelis and Maurizio D’Amario and Simone Zazzeroni and Christian Ciampoli and Sergio Caputi},
  journal={Operative dentistry},
  year={2009},
  volume={34 3},
  pages={
          328-36
        }
}
Microtensile bond strength (microTBS) evaluation and fractographic analysis were used to compare four luting systems in the cementation of resin-based composite (RBC) and ceramic disks to dentin. Forty freshly-extracted molars were transversally sectioned to expose flat, deep dentin surfaces. Forty cylindrical specimens (5-mm diameter and 10-mm height), consisting of 20 RBC disks and 20 leucite-based glass ceramic disks, were produced. The RBC disks were sandblasted with 50-microm Al2O3. The… 

Figures and Tables from this paper

Bond strength evaluation of three self-adhesive luting systems used for cementing composite and porcelain.
TLDR
A microtensile bond strength test was used to compare three self-adhesives, an etch-and-rinse and a self-etch luting system, in the cementation of resin-based composite (RBC) and ceramic disks to dentin, and the UniCem group showed the lowest number of preterm failures among the testedSelf-adhesive systems.
Bonding Effectiveness of Contemporary Materials in Luting Glass-Ceramic to Dentine: An In Vitro Study
TLDR
Flowable composites can be alternatives to resin cements when bonded with total-etch procedures and self-adhesive protocols as well as shear bond strength when bond strength is still to be developed.
Assessment of Microtensile Bond Strength of Different Resin Cements Used for Luting of Indirect MOD Resin Composite Inlays to Dentin after Aging in Different Media
TLDR
Resin cement type and aging media/time had a substantial effect on the microtensile bond strength at cement/dentin interface.
Evaluation of Micro-Tensile Bond Strength of Indirect Resin Composite Inlay to Dentin
TLDR
Evaluated micro-tensile bond strength (μTBS) of indirect resin composite inlay to dentin after specimen's storage in distilled water and lactic acid showed good results with SE resin cement strategy.
Push-out bond strength of CAD/CAM-ceramic luted to dentin with self-adhesive resin cements.
Influence of selective acid etching on microtensile bond strength of a self-adhesive resin cement to enamel and dentin
TLDR
Acid etching prior to RelyX Unicem application did not improve microtensile bond strength for enamel and dentin, and all luting strategies presented similar dentin bond strength, but significantly lower than enamel bond strength.
Ceramic Inlays: Effect of Mechanical Cycling and Ceramic Type on Restoration-dentin Bond Strength.
TLDR
The composition and manufacturing process of ceramics seem to have an influence on the ceramic surface and resin cement bond strength in permanent maxillary premolars, with and without mechanical cycling.
Bond Strengths of Two Self-adhesive Resin Cements to Dentin with Different Treatments
TLDR
It can be concluded that phosphoric acid etching improved bond strength of the two self-adhesive resin cements applied to dentin surfaces treated with different methods.
A study of self-adhesive resin cements for bonding to silver-palladium-copper-gold alloy -- effect of including primer components in cement base.
TLDR
Results showed that Clearfil SA Luting, Maxcem, and RelyX Unicem Clicker were efficacious for bonding to Ag-Pd-Cu-Au alloy after air abrasion surface treatment for the latter.
...
...

References

SHOWING 1-10 OF 41 REFERENCES
Microtensile bond strength of self-adhesive luting cements to ceramic.
TLDR
The null hypothesis was rejected: materials showed different tensile bond strengths, and RelyX Unicem, the only material that does not require pretreatment of dentin, achieved the lowest TBS values under these study conditions.
Dentin bond strength and marginal adaptation: direct composite resins vs ceramic inlays.
TLDR
In general, third- and fourth-generation dentin adhesives produced better results in bond strength and marginal adaptation than one-bottle systems (P < 0.05) and precuring of the bonding resin prior to insertion of adhesive inlays cannot be recommended clinically, because the 120-micron luting spaces were too large.
Micro-tensile bond testing of resin cements to dentin and an indirect resin composite.
Bond durability of composite luting agents to ceramic when exposed to long-term thermocycling.
TLDR
There were significant differences among the four resin composite cements in terms of their bonding effectiveness to GN-I CAD-CAM ceramic after thermocycling, which highlights the need for material specifications.
Tensile bond strength of four resin luting agents bonded to bovine enamel and dentin.
Microtensile bond strength of several adhesive systems to different dentin depths.
TLDR
The bond strengths of Prime & Bond NT and Excite were significantly higher to deep than to superficial dentin and the rest of the adhesives showed similar bond strength to both dentin depths, while Single Bond, Prime&Bond NT and Clearfil SE Bond performed equally when were bonded to superficial teeth.
Bonding effectiveness of adhesive luting agents to enamel and dentin.
Effects of restorative and adhesive curing methods on dentin bond strengths.
TLDR
Two adhesives, light-cured Prime & Bond NT and OptiBond Solo Plus, had significantly lower bond strengths when used with the self-cure composite, compared with other "one-bottle" dentinAdhesives.
Shear bond strength of resin cements to both ceramic and dentin.
TLDR
Hydrofluoric acid-etching followed by silane application produced the best bonds at 24 hours and 6 months with all 4 cements, and both auto- and light-polymerized dentin bonding agents bonded better to dentin than dual- polymerized bonding agents.
...
...