Simultaneous co-deposition of SiC and CNT into the Ni coating

@article{Mosallanejad2016SimultaneousCO,
  title={Simultaneous co-deposition of SiC and CNT into the Ni coating},
  author={Mohammad Hossein Mosallanejad and Ali Shafyei and S. Akhavan},
  journal={Canadian Metallurgical Quarterly},
  year={2016},
  volume={55},
  pages={147 - 155}
}
Various researches are carried out to investigate the properties of Ni-SiC and Ni-CNT composite coatings. The simultaneous effect of carbon nanotube (CNT) and silicon carbide (SiC) is not addressed in the literature. Hence, Ni-SiC and Ni-SiC-CNT nanocomposite coatings were electrodeposited on aluminium substrate in this paper. Surface hardness and elastic modulus of the coatings were measured by atomic force microscope, and X-ray diffraction technique was used to evaluate the grain size of the… 

Simultaneous co-deposition of SiC and CNT into the Ni coating

Various researches are carried out to investigate the properties of Ni-SiC and Ni-CNT composite coatings. The simultaneous effect of carbon nanotube (CNT) and silicon carbide (SiC) is not addressed

Assessment of the Performance of Ni-Carbon Nanotube Nanocomposite Coatings for Protecting the Surfaces of Steel Agricultural Mower Knives

In this study, nanotechnology is used to improve the wear and corrosion resistance of reciprocating mower knives. In particular, carbon nanotubes (CNTs) are used to reinforce the Ni-metal matrix, and

Characteristics and properties of Cu/nano-SiC and Cu/nano-SiC/graphite hybrid composite coatings produced by pulse electrodeposition technique

ABSTRACT In this study, Cu/SiC and Cu/SiC/graphite nano-composite coatings were prepared by using pulse current electrodeposition technique. The effects of pulse parameters and graphite particles

Electrodeposition of Graphene Oxide Modified Composite Coatings Based on Nickel-Chromium Alloy

Composite electrochemical coatings (CECs) based on nickel-chromium alloy and modified with multilayer graphene oxide (GO) were obtained. The electrodeposition process of these coatings was studied in

On the Electrochemical Deposition and Properties of Nickel-Based Composite Coatings

Abstract Nickel-based composite electrochemical coatings (CECs) modified with graphite nitrate have been obtained. Their microstructure and functional properties (sliding friction coefficient and

Electrodeposition and Corrosion Properties of Nickel–Graphene Oxide Composite Coatings

Tests in a 3.5% NaCl solution showed that the inclusion of GO particles into the composition of electrolytic nickel deposits makes their corrosion rate 1.40–1.50 times less.

Electrochemical Deposition of Composite Nickel–Graphene Oxide Coatings in the Reverse Mode

Nickel-based composite electrochemical coatings (CECs) modified with multilayer graphene oxide (GO) from a sulfate-chloride electrolyte in a reverse electrolysis mode have been obtained. The

Study of Electrodeposition and Functional Properties of Nickel-Graphite Bisulfate Composite Coatings

Nickel-based composite electrochemical coatings modified with graphite bisulfate were obtained. The functional properties (sliding friction coefficient, protective capacity) of these coatings as

Fabrication and Characterization of the Modified EV31-Based Metal Matrix Nanocomposites

Metal matrix nanocomposites (MMNCs) with high specific strength have been of interest for numerous researchers. In the current study, Mg matrix nanocomposites reinforced with AlN nanoparticles were

References

SHOWING 1-10 OF 30 REFERENCES

Simultaneous co-deposition of SiC and CNT into the Ni coating

Various researches are carried out to investigate the properties of Ni-SiC and Ni-CNT composite coatings. The simultaneous effect of carbon nanotube (CNT) and silicon carbide (SiC) is not addressed