Rheological and Mechanical Properties of PC/HDPE/glass fiber Composites

@article{Li2002RheologicalAM,
  title={Rheological and Mechanical Properties of PC/HDPE/glass fiber Composites},
  author={Chaoqin Li and Yong Zhang and Yinxi Zhang and Changming Zhang},
  journal={Polymers and Polymer Composites},
  year={2002},
  volume={10},
  pages={619 - 626}
}
The rheological behaviour and mechanical properties of the polycarbonate/high density polyethylene/glass fiber (PC/HDPE/GF) composites have been studied, along with fiber-resin interface behaviour. Maleic anhydride grafted low density polyethylene (LDPE-g-MAH) was used as a compatibilizer in the composites. A study of the glass fiber-resin interface by scanning electron microscopy (SEM) and by etching techniques indicated that the dispersed phase polymer in the composites preferentially adhered… 

Figures and Tables from this paper

Effect of nanoclay in HDPE–glass fiber composites on processing, structure, and properties
Natural Na+ montmorillonite (MMT) microclay and organo-treated MMT nanoclay were independently filled in a high-density polyethylene (HDPE) polymer and HDPE–glass fiber (GF) composite and the
The effect of annealing on the melt rheology of ternary PE/PA6/GF composites
Abstract Ternary composites have been prepared by simultaneous extrusion of polyethylene (PE), polyamide-6 (PA6) and short glass fibre (GF) reinforcement. Two types of fibres – compatible either to
The strain dependence of the dynamic moduli of short fiber reinforced thermoplastic blends
In the present work we relate the microstructure of a distinct type of short fiber reinforced blends (SFRBs) to their melt rheology. These systems consist of polyamide-6 (PA6) and short glass fiber
Thermal and mechanical properties of glass fibre reinforced polyphenylene ether/polystyrene/nylon-6 ternary blends
This paper deals with fabrication and characterization of unique polyphenylene ether/polystyrene/nylon-6/glass composites. Compounding of ternary blends with glass fibres was performed using twin
Evolution of the morphology and the mechanical properties of ternary PE/PA6/GF composites during annealing
Ternary composites have been prepared via simultaneous melt extrusion of polyethylene (PE), polyamide-6 (PA6) and short glass fibres in a twin screw extruder. If the fibres are compatible with PA6 a
Rheological behavior comparison between PET/HDPE and PC/HDPE microfibrillar blends
The rheological behaviors of in situ microfibrillar blends, including a typical semicrystalline/semicrystalline (polyethylene terephthalate (PET)/high-density polyethylene (HDPE)) and a typical
Morphology and Rheological Behaviors of Polycarbonate/High Density Polyethylene in situ Microfibrillar Blends
Summary: Polycarbonate (PC)/high density polyethylene (HDPE) in situ microfibrillar blends were fabricated by a slit die extrusion, hot stretching, and quenching process. Despite PC and HDPE having a
Mechanical and rheological properties of carbon nanotube-reinforced polyethylene composites
Abstract This paper investigates some mechanical and rheological properties of low density polyethylene (LDPE) composites reinforced by multi-walled carbon nanotubes (MWNTs). It was found that the
Effects of silanization and modification treatments on the stiffness and toughness of BF/SEBS/PA6,6 hybrid composites
Abstract To develop basalt fiber (BF)-reinforced PA6,6 composites with an optimal balance between stiffness and toughness, the effects of fiber surface treatments and the addition of rubber
Nonisothermal crystallization behavior of LLDPE/glass fiber composite
The nonisothermal crystallization behavior of linear low-density polyethylene (LLDPE)/glass fiber (GF) composite was investigated by differential scanning calorimetry (DSC). It was observed that the
...
1
2
...

References

SHOWING 1-10 OF 13 REFERENCES
Glass-fiber-reinforced polypropylene/EPDM blend. I. Melt rheological properties
Melt rheological properties of the blend of isotactic polypropylene (PP) and ethylene propylene diene rubber (EPDM) at varying ratios and of the glass fiber (GF) filled PP and PP/EPDM blend by
The role of interfacial contact in immiscible binary polymer blends and its influence on mechanical properties
In this paper an immiscible blend comprised of a crystalline(polyethylene) and an amorphous(polycarbonate) component was studied. Depending on whether the crystalline material is the dispersed phase
Studies on high density polyethylene/polycarbonate blend system compatibilized with low density polyethylene grafted diallyl bisphenol A ether
Blends of a high density polyethylene (HDPE) matrix and a polycarbonate (PC) minor phase were investigated through their morphology, heat resistance, mechanical properties, crystallizing behavior,
Interfacial component of glass fiber in ternary composites of GF/PC/PP: effect of the preferential encapsulation of glass fiber
We investigated the encapsulation phenomena of glass fibers for a ternary composite system of glass fiber, polycarbonate and polypropylene by impregnating fibers with a selected resin using a newly
Influence of miscibility on the morphology and properties of polycarbonate/(maleic anhydride)-grafted-polypropylene blend
Maleic-anhydride-grafted polypropylene (MAH-g-PP) was added to polycarbonate (PC) as a processing agent. Its influence on the morphological, thermal, rheological, and mechanical properties of
Glass fiber reinforced polypropylene/EPDM blends. II. Mechanical properties and morphology
Tensile and impact properties of the ternary system polypropylene (PP)/ethylene propylene diene elastomer (EPDM)/glass fiber (GF) and the corresponding binary systems PP/EPDM blend and PP/GF
Melt viscosity of polycarbonate–polyolefin blends
The flow behavior of polycarbonate (PC) blended with three kinds of polyolefins (LDPE, HDPE, PP) was studied at 260°C using an Instron Capillary Rheometer. Flow behavior of the blends was found to be
Structuring of binary PP/PA-6 blends and ternary PP/PA-6/GF blends
Morphological development under shear flow conditions for binary polypropylene (PP)-polyamide-6 (PA-6) and ternary PP-PA-6-glass fiber blends has been investigated. The shear viscosity was determined
Interfacial adhesion and toughening mechanisms in an alloy of polycarbonate/polyethylene
Abstract Interfacial adhesion and toughening mechanisms in an alloy of polycarbonate/polyethylene (PC/PE) are investigated using transmission electron microscopy. In contrast to the general
Fiber fracture in reinforced thermoplastic processing
The length reduction of reinforcing fibers in short-fiber reinforced plastics during processing has been studied experimentally. It has been shown that fiber volume fraction, initial length, and
...
1
2
...