• Corpus ID: 212522768

Regenerative Braking System of Electric Vehicle Driven By BLDC Motor Using Neuro- Fuzzy and PID

@inproceedings{Sindhuja2014RegenerativeBS,
  title={Regenerative Braking System of Electric Vehicle Driven By BLDC Motor Using Neuro- Fuzzy and PID},
  author={V. Sindhuja and G. Ranjitham},
  year={2014}
}
Regenerative braking can improve energy usage efficiency and can extend the driving distance of Electric Vehicles. Innovative Regenerative Braking System of EV driven by BLDC motor is recommended. In this technique, Brushless DC motor is controlled by traditional Proportional Integral Derivative control, and the braking force distribution is done by ANFIS. This reasoning is quite sluggish compared to PID. Thus PID is used to control the negative torque of the motor when brake is pressed. This… 

Figures and Tables from this paper

References

SHOWING 1-10 OF 14 REFERENCES

A Cost-Effective Method of Electric Brake With Energy Regeneration for Electric Vehicles

The proposed solution simultaneously achieves dual goals of the electric brake and the energy regeneration without using additional converter, ultracapacitor, or complex winding-changeover technique.

A Series Regenerative Braking Control Strategy Based on Hybrid-Power

A regenerative braking system, which could restore kinetic energy and potential energy to a battery or any other forms of power during braking, is a special system for electric and hybrid electric

Digital Control Strategy for Four Quadrant Operation of Three Phase BLDC Motor With Load Variations

The digital controller dsPIC30F4011, which is very advantageous over other controllers, as it combines the calculation capability of Digital Signal Processor and controlling capability of PIC microcontroller, to achieve precise control.

An FPGA-Based Novel Digital PWM Control Scheme for BLDC Motor Drives

This paper lays the groundwork for the development of a new low-cost IC for control of BLDC motors by implementing a simple novel digital pulsewidth-modulation control for a trapezoidal BLDC motor drive system.

Driving and Braking Torque Distribution Methods for Front- and Rear-Wheel-Independent Drive-Type Electric Vehicles on Roads With Low Friction Coefficient

  • N. Mutoh
  • Engineering
    IEEE Transactions on Industrial Electronics
  • 2012
A driving torque Distribution method when cornering and a braking torque distribution method; these methods are related to the third characteristic, and they are particularly effective when driving on roads with ultralow μ, such as icy roads.

Hybrid Excitation Topologies and Control Strategies of Stator Permanent Magnet Machines for DC Power System

  • Yu WangZ. Deng
  • Engineering, Physics
    IEEE Transactions on Industrial Electronics
  • 2012
The electromagnetic performance of different hybrid excitation stator PM machines according to different combination modes of PMs, excitation winding, and iron flux bridge is compared and an improved direct torque control (DTC) strategy is investigated to improve system performance.

Design and Implementation of Fuzzy Control on a Two-Wheel Inverted Pendulum

This paper introduces the design and implementation of a two-wheel inverted pendulum (TWIP) system with a fuzzy control scheme and the system-on-a-programmable-chip (SoPC) technology. The control

Dynamics of Front-and-Rear-Wheel-Independent-Drive-Type Electric Vehicles at the Time of Failure

Failsafe performance at the time of failure was evaluated on test courses, including roads having an ultra-low friction coefficient and showed that even if failure occurred while cornering and when running on low- μ roads, the FRID EV continued to run stably.

PID control system analysis, design, and technology

It is seen that many PID variants have been developed in order to improve transient performance, but standardising and modularising PID control are desired, although challenging, and the inclusion of system identification and "intelligent" techniques in software based PID systems helps automate the entire design and tuning process to a useful degree.

Overview of Stator-Permanent Magnet Brushless Machines

An overview of the stator-PM machine is presented, with particular emphasis on concepts, operation principles, machine topologies, electromagnetic performance, and control strategies.