Influence of water storage on fatigue strength of self-etch adhesives.

@article{Takamizawa2015InfluenceOW,
  title={Influence of water storage on fatigue strength of self-etch adhesives.},
  author={Toshiki Takamizawa and Wayne W. Barkmeier and Akimasa Tsujimoto and Donal D Scheidel and Hidehiko Watanabe and Robert L. Erickson and Mark A Latta and Masashi Miyazaki},
  journal={Journal of dentistry},
  year={2015},
  volume={43 12},
  pages={
          1416-27
        }
}

Influence of different pre-etching times on fatigue strength of self-etch adhesives to dentin.

TLDR
Reducing phosphoric acid pre-etching time can minimize the adverse effect on dentin bonding durability for the conventional self-etch adhesives.

Influence of different smear layers on bond durability of self-etch adhesives.

Influence of Etching Mode on Enamel Bond Durability of Universal Adhesive Systems.

TLDR
Although the influence of different etching modes on the enamel-bonding performance of universal adhesives was found to be dependent on the adhesive material, total-etch mode effectively increased the enameless bond strength and durability, as measured by fatigue testing.

Bond durability of universal adhesive to bovine enamel using self-etch mode

TLDR
The present data indicate that the enamel bond durability of universal adhesives in the self-etch mode might be sufficient for clinical use, compared to the bond strengths obtained with the two-stepSelf-etch adhesive.

Influence of frequency on shear fatigue strength of resin composite to enamel bonds using self-etch adhesives.

Influence of degradation conditions on dentin bonding durability of three universal adhesives.

Effect of Active Application on Bond Durability of Universal Adhesives.

TLDR
Active application is effective in enhancing the dentin bond durability of universal adhesives with different etching modes and practitioners should select the optimal etching mode and appropriate application method in accordance with the cavity conditions.

Enamel and Dentin Bond Durability of Self-Adhesive Restorative Materials.

TLDR
SBS and SFS values to enamel were similar for all materials tested except Activa which generated lower enamel values, and on dentin surfaces, the self-adhesive materials generated similar SBS andSFS, with the exception of Activa.

Effect of double-layer application on bond quality of adhesive systems.

Influence of the number of cycles on shear fatigue strength of resin composite bonded to enamel and dentin using dental adhesives in self-etching mode.

TLDR
Regardless of the adhesive used in self-etch mode for bonding to enamel or dentin, shear fatigue strength was not influenced by the number of cycles used for sheer fatigue strength testing.

References

SHOWING 1-10 OF 44 REFERENCES

Effect of Phosphoric Acid Pre-etching on Fatigue Limits of Self-etching Adhesives.

TLDR
The effect of using phosphoric acid, prior to the application of the self-etching adhesives, on SBS and SFL was dependent on the adhesive material and tooth substrate and should be carefully considered in clinical situations.

Bonding durability of single-step adhesives to previously acid-etched dentin.

TLDR
From the results of this in vitro study, prior acid etching might be not acceptable for increasing the dentin bond strengths of single-step self-etch adhesive systems.

Effect of prior acid etching on bonding durability of single-step adhesives.

TLDR
Through a careful choice of adhesive system, prior acid etching can increase the bond strengths of single-step self-etch adhesive systems.

Fatigue of enamel bonds with self-etch adhesives.

Bond strength of self-etch adhesives to pre-etched enamel.

Effect of dentin location and long-term water storage on bonding effectiveness of dentin adhesives.

TLDR
In conclusion, only for the mild self-etch adhesives, µTBS to 'periphery' dentin was higher than for the 'center' specimens, and regional variability did not affect the long-term bonding effectiveness for any of the adhesive tested.

Dentin bond strengths of four adhesion strategies after thermal fatigue and 6-month water storage.

  • A. SezinandoJ. PerdigãoRita Regalheiro
  • Medicine, Materials Science
    Journal of esthetic and restorative dentistry : official publication of the American Academy of Esthetic Dentistry ... [et al.]
  • 2012
TLDR
The self-etch adhesion strategies XTR and AIO performed similarly or better than the etch-and-rinse adhesives FL and SOLO for all three testing conditions, and their aging stability seems to be material-dependent.

In vitro degradation of resin-dentin bonds with one-bottle self-etching adhesives.

TLDR
The deterioration of the oxygen-inhibition zone in the adhesive-resin composite junction resulted in a decrease in bond strength after 100 d in water for one-bottle self-etching adhesives.

Influence of ageing on self-etch adhesives: one-step vs. two-step systems.

TLDR
Immediate bond strength, nanoleakage expression, and stability over time were not related to the number of steps of the bonding systems, but to their chemical formulations.

Effect of enamel etching time on roughness and bond strength.

TLDR
The current study examined the effect of different enamel conditioning times on surface roughness and bond strength using an etch-and-rinse system and four self-etch adhesives to determine Ra and SBS values, which were significantly greater than all theSelf-etch systems and controls.