Correlation of Yield Strength and Tensile Strength with Hardness for Steels

@article{Pavlina2008CorrelationOY,
  title={Correlation of Yield Strength and Tensile Strength with Hardness for Steels},
  author={Erik J. Pavlina and Chester J. Van Tyne},
  journal={Journal of Materials Engineering and Performance},
  year={2008},
  volume={17},
  pages={888-893}
}
  • E. Pavlina, C. J. Tyne
  • Published 3 April 2008
  • Materials Science
  • Journal of Materials Engineering and Performance
Hardness values as well as yield and tensile strength values were compiled for over 150 nonaustenitic, hypoeutectoid steels having a wide range of compositions and a variety of microstructures. The microstructures include ferrite, pearlite, martensite, bainite, and complex multiphase structures. The yield strength of the steels ranged from approximately 300 MPa to over 1700 MPa. Tensile strength varied over the range of 450-2350 MPa. Regression analysis was used to determine the correlation of… 
On the Prediction of Strength from Hardness for Copper Alloys
Hardness and strength values of over 55 copper alloys strengthened by solid solution strengthening, precipitation hardening, cold working, and dispersion strengthening were compiled. The yield
Uniform Elongation and the Stress-Strain Flow Curve of Steels Calculated from Hardness Using Empirical Correlations
An empirical relationship between the hardness and uniform elongation of non-austenitic hypoeutectoid steels has been developed. This new hardness-elongation relationship was combined with previously
Prediction of microstructure and mechanical properties of line pipe welded joints based on hardness map
In this article, the variation of hardness in cross-section of X52 microalloyed steel joints before and after post-weld heat treatment and also the relationship of hardness with ultimate tensile
Hardness–strength relationships in the aluminum alloy 7010
Abstract The relationship between Vickers hardness, yield stress and tensile strength was analyzed by combining data from two independent studies involving 7010 alloy plate and a rectilinear forging.
An Experimental Investigation of Relationship between surface Hardness and Strength of Locally produced TMT 500W bar in Bangladesh
The high-strength mild steel bars (usually low carbon steel) are widely used for structural purposes throughout the world including Bangladesh. The strength of these deformed barsis measured through
Theoretical Conversions of Different Hardness and Tensile Strength for Ductile Materials Based on Stress–Strain Curves
  • H. Chen, L. Cai
  • Materials Science
    Metallurgical and Materials Transactions A
  • 2018
Based on the power-law stress–strain relation and equivalent energy principle, theoretical equations for converting between Brinell hardness (HB), Rockwell hardness (HR), and Vickers hardness (HV)
Empirical Relationship between Hardness and Tensile Properties of High Pressure Torsion-processed Al 6061
Improved strength is the ultimate goal of advanced material processing technique, including high-pressure torsion (HPT). To evaluate this goal, it requires determination of strength properties of the
Assessment and statistical correlation of mechanical properties of double sided single pass submerged arc welded line pipe steel
Abstract This study aims to assess mechanical properties of submerged arc welded, high-strength, line pipe steel API X70. The obtained weldment as well as the base metal were assessed for strength,
Critical Evaluation of Spherical Indentation Stress-Strain Protocols for the Estimation of the Yield Strengths of Steels
Accelerated development of advanced metals and alloys requires validated relationships between the high throughput indentation measurements and standardized tensile test protocols. The main objective
Mechanical properties and microstructural evaluation of the heat-affected zone in ultra-high strength steels
Abstract This paper presents an investigation into the mechanical properties of ultra-high strength steels (UHSSs) (with nominal yield stress of 960 and 1100 MPa) after welding. Seven weld thermal
...
1
2
3
4
5
...

References

SHOWING 1-10 OF 11 REFERENCES
Section thickness, macrohardness and yield strength in high-pressure diecast magnesium alloy AZ91
The yield strength of high-pressure diecast (hpdc) test bars of alloy AZ91 increases with decreasing section thickness while its hardness remains approximately constant. This behaviour is in contrast
Correlation of the hot-hardness with the tensile strength of 304 stainless steel to temperatures of 1200°C
It is shown that the ultimate tensile strength, σ, of 304 stainless steel can be correlated with hot-hardness measurements at temperatures up to 1200°C using the expression σ = (H/3.0)(n/0.2n)n
Correlation of hot-microhardness with elevated-temperature tensile properties of low activation ferritic steel
Hot microhardness and elevated temperature tensile tests have been performed on 9Cr-2.5W-0.3V-0.15C (GA3X) low activation ferritic steel at temperatures from 20°C to 650°C. The uniform elongation of
The determination of yield strength from hardness measurements
It is shown that the 0.2 pct offset yield strength of a material (in kg per sq mm) can be obtained from simple hardness measurements using the expression σy = (H/3)(0.1)m-2, whereH is the Diamond
Microhardness mapping and the hardness-yield strength relationship in high-pressure diecast magnesium alloy AZ91
Microhardness maps of cross-sections of high-pressure diecast test bars of AZ91 have been determined. Specimens with rectangular cross-sections, 1, 2 and 3 mm thick, or with a circular cross-section
On the correlation of mechanical and physical properties of 7075-T6 Al alloy
Abstract The influence of varying the thermal processing parameters on the physical and mechanical properties of 7075 T6 aluminum alloy was studied. The variables altered were solution treatment
Effects of induction hardening and prior cold work on a microalloyed medium carbon steel
The torsional strength and microstructural response to induction hardening of a 10V45 steel with prior cold work was evaluated. The vanadium-microalloyed 1045 (10V45) steel was characterized in three
A New Approach to Plasticity and Its Application to Blunt Two Dimensional Indenters
The classical slip line field solution for a two-dimensional punch is found to give a constraint factor (2.57) which i s too small when the specimen beneath the punch is extensive. A new approach
...
1
2
...