Analytical model for the approximation of hysteresis loop and its application to the scanning tunneling microscope

@article{Lapshin2020AnalyticalMF,
  title={Analytical model for the approximation of hysteresis loop and its application to the scanning tunneling microscope},
  author={Rostislav V. Lapshin},
  journal={ArXiv},
  year={2020},
  volume={abs/2006.02784}
}
  • R. Lapshin
  • Published 1 September 1995
  • Engineering
  • ArXiv
A new model description and type classification carried out on its base of a wide variety of practical hysteresis loops are suggested. An analysis of the loop approximating function was carried out; the parameters and characteristics of the model were defined—coersitivity, remanent polarization, value of hysteresis, spontaneous polarization, induced piezocoefficients, value of saturation, hysteresis losses of energy per cycle. It was shown that with piezomanipulators of certain hysteresis loop… 

Figures and Tables from this paper

An improved parametric model of hysteresis loop
  • R. Lapshin
  • Engineering
    The Review of scientific instruments
  • 2020
TLDR
Three phase shifts are included in the model, which permits us to tilt the hysteresis loop smoothly by the required angle at the split point as well as to smoothly change the curvature of the loop.
Advanced hysteresis method for early damage detection of fastening systems in concrete under fatigue load
  • M. Hoepfner
  • Engineering, Materials Science
    Beton- und Stahlbetonbau
  • 2018
This paper presents an advanced method for the characterization of the fatigue failure and corresponding load process of fastening systems in concrete. The required hysteresis model is based on
Advanced Development of Hysteresis Measurement Characteristics for Early Detection of Fatigue Damages on Fasting Systems in Concrete
  • M. Hoepfner
  • Engineering, Materials Science
    Structural Integrity
  • 2019
This paper presents an advanced hysteresis measurement model for the characterization of fatigue failures and corresponding, time-dependent damage processes until final failure of fastening systems
Modeling forces between the probe of atomic microscope and the scanning surface
TLDR
The proposed neural network is well capable of modeling the behavior of AFM probes in noncontact mode and is found to be a feed-forward backpropagation network, with Logsig, Tansig and TansIG transfer functions in successive layers, respectively, and 3 and 2 neurons in the first and second hidden layers.
On the relationship between mechanical energy rate and heat dissipated rate during fatigue for a C45 steel depending on stress ratio
This work deals with the analysis in the frequency domain of the temperature signal and mechanical energy rate of C45 steel under two different fatigue stepwise loading series at stress ratios of 0.1
Measurement and Modeling of Hysteresis in Pneumatic Actuator Under Different Loading Rate
A hysteresis model under different loading rate is proposed based on measurement results with simple polynomial method. This model will be used for better control and compensation of pneumatic
Measurements error propagation and its sensitivity analysis in the aero-engine multistage rotor assembling process.
TLDR
It is concluded that linear guide alignment error and verticality error are the primary error sources, and the angle error of the turntable need to be improved.
Thermal Hysteresis Involving Reversible Self-Catalytic Reactions.
TLDR
This Account describes thermal hysteresis caused by molecules dispersed in dilute solutions containing optically active helicene oligomers, which form homo- and heterodouble helices, the cooling and heating processes of which cause different structural changes with regard to their relative concentrations.
...
1
2
...

References

SHOWING 1-10 OF 16 REFERENCES
Calibration and characterization of piezoelectric elements as used in scanning tunneling microscopy
We investigated the behavior of piezoelectric elements used in an STM for fine positioning of the tip. Special attention was paid to the influence of hysteresis. We found that the expansion
Correction of geometrical distortions in scanning tunneling and atomic force microscopes caused by piezo hysteresis and nonlinear feedback
Geometrical distortions of scanning tunneling or atomic force microscope pictures can be caused by delayed response of the piezo‐ceramics and errors of the nonlinear feedback system. The images are
Fast-acting piezoactuator and digital feedback loop for scanning tunneling microscopes
The design of a sectional piezoactuator is described, and the principle of operation of a tunnel junction digital stabilization system is given. The total settling time of the system while the least
Deformations and nonlinearity in scanning tunneling microscope images
We perform here a complete determination of the relation between applied voltage and displacement for a tripod piezoceramic scanning tunneling microscope (STM) scanner unit. The absolute calibration
Optical scan‐correction system applied to atomic force microscopy
Nonlinearities inherent in the piezoelectric actuators used in high‐resolution scanning probe microscopies limit the usefulness of the instruments for precision dimensional measurements of
Some design criteria in scanning tunneling microscopy
  • D. Pohl
  • Physics
    IBM J. Res. Dev.
  • 1986
TLDR
Design rules are presented for the optimization of damping, stiffness, electrical control circuitry, and the performance of the piezoelectric actuators usually employed in STMs.
Fatigue Deformation Mechanisms of Zirconia Ceramics
Two distinct fatigue deformation mechanisms, microcracking and transformation plasticity, have been identified in 3Y-TZP and Mg-PSZ. Microcracking is dominant in 3Y-TZP, while transformation
Processing Effects in the Sol–Gel Preparation of PZT Dried Gels, Powders, and Ferroelectric Thin Layers
This paper reports on infrared spectroscopy that was used to monitor and characterize solutions used in the preparation of PZT 53/47 powders, dried gels, and thin layers deposited on platinized
...
1
2
...