A monitoring and control test bench for assessing the upgraded low voltage power supplies for the ATLAS Tile Calorimeter Phase-II Upgrade front-end electronics

@article{Nkadimeng2022AMA,
  title={A monitoring and control test bench for assessing the upgraded low voltage power supplies for the ATLAS Tile Calorimeter Phase-II Upgrade front-end electronics},
  author={Edward Nkadimeng and R. Mckenzie and Seyedali Moayedi and Stanislav Nemecek and Haleh Khani Hadavand and Bruce Mellado and Roger van Rensburg},
  journal={Journal of Instrumentation},
  year={2022},
  volume={17}
}
The ATLAS detector is set to undergo a substantial upgrade termed the “Phase-II” upgrade during the Long-Shutdown in preparation for the start of operation of the High Luminosity Large Hadron Collider (HL-LHC). This paper describes the development and implementation of the Phase-II upgrade low voltage power supply transformer-coupled buck converter (Brick) test bench. A large scale production of approximately 2048 finger low voltage power supplies, with an identical output voltage, is set to be… 

References

SHOWING 1-10 OF 13 REFERENCES
Upgrade of ATLAS Hadronic Tile Calorimeter for the High Luminosity LHC
  • R. Mckenzie
  • Physics
    Proceedings of The Ninth Annual Conference on Large Hadron Collider Physics — PoS(LHCP2021)
  • 2021
The Tile Calorimeter (TileCal) is a sampling hadronic calorimeter covering the central region of the ATLAS experiment, with steel as an absorber and plastic scintillators as the active medium. The
Upgrade of ATLAS Hadronic Tile Calorimeter for the High Luminosity LHC
The Tile Calorimeter (TileCal) is a sampling hadronic calorimeter covering the central region of the ATLAS experiment, with steel as absorber and plastic scintillators as the active medium. The
The ATLAS Experiment at the CERN Large Hadron Collider
This paper describes the ATLAS experiment as installed in i ts experimental cavern at point 1 at CERN. It also presents a brief overview of the expec ted performance of the detector.
ATLAS TileCal low voltage power supply upgrade hardware and testing
Radiation-Tolerant Custom Made Low Voltage Power Supply System for ATLAS/TileCal Detector
This paper describes custom made Low Voltage Power Supply (LVPS) system developed for the ATLAS – TileCal detector of the LHC (The Large Hadron Collider) particle accelerator at CERN, Geneva. The
LabView advanced programming techniques
Introduction to LabVIEW Virtual Instruments LabVIEW Projects Help Data Flow Programming Menus and Palettes Front Panel Controls User Control Sets Block Diagram Functions Setting Options LabVIEW
The ATLAS Experiment at the CERN Large Hadron Collide
The ATLAS detector as installed in its experimental cavern at point 1 at CERN is described in this paper. A brief overview of the expected performance of the detector when the Large Hadron Collider
An upgraded front-end switching power supply design for the ATLAS TileCAL detector of the LHC
TLDR
An upgraded switching power supply brick for the front-end electronics of the ATLAS hadron tile calorimeter (TileCAL) at the LHC features significant improvement in noise, improved fault detection, and generally a more robust design, while retaining the compact size, water-cooling, output control, and monitoring features in this 300 KHz design.
The new front-end electronics for the ATLAS tile calorimeter phase 2 upgrade
  • G. Drake
  • Physics
    2015 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC)
  • 2015
We present the design for the new read out system being developed for the Phase 2 Upgrade of the ATLAS Tile Calorimeter. The front-end electronics will be replaced to address the increase in beam
Readiness of the ATLAS Tile Calorimeter for LHC collisions
TLDR
An overview of the Tile Calorimeter performance as measured using random triggers, calibration data, data from cosmic ray muons and single beam data and the determination of the global energy scale was performed with an uncertainty of 4%.
...
...