Z. Burzi

Publications19
h-index1
Citations5
Highly Influential Citations0
Claim Author Page
Author pages are created from data sourced from our academic publisher partnerships and public sources.

Recommended Authors

  • A. Sedmak
  • 188 Publications, 867 Citations
  • S. Sedmak
  • 42 Publications, 97 Citations
  • Z. Burzić
  • 83 Publications, 237 Citations
  • N. Gubeljak
  • 192 Publications, 790 Citations
  • Publications
  • Influence
Z. BURZI] ET AL.: FATIGUE PROPERTIES OF A HIGH-STRENGTH-STEEL WELDED JOINT FATIGUE PROPERTIES OF A HIGH-STRENGTH-STEEL WELDED JOINT
In addition to the strength and toughness properties, the fatigue properties of welded joints are necessary for the design of high-strength steel structures exposed to variable loading. Wöhler curves… Expand
FINAL STRETCH ZONE WIDTH DETERMINATION FOR MP35N MULTIPHASE ALLOY ODREĐIVANJE ŠIRINE ZONE KONAČNOG RAZVLAČENJA MP35N VIŠEFAZNE LEGURE
This paper presents an experimental elastic-plastic fracture behaviour analysis in order to evaluate a resistance of the aged and unaged MP35N alloy to stable and unstable crack growth. MP35N… Expand
  • 1
  • PDF
Low cycle fatigue of weldments produced of a high strength low alloyed steel
A quenched and tempered high strength low alloy steel NIONIKRAL 70 for producing welded pressure vessels, where high resistance to fatigue crack propagation and high tolerance of damage are of high… Expand
Trends in the Development of Machinery and Associated Technology ” TMT 2011 , Prague , Czech Republic , 12-18 September 2011 STRESS STATE OF BOILER TUBES FOR STRUCTURAL INTEGRITY ASSESSMENT
The change of state during and after water pressure proof test was monitored by strain gauges and acoustic emission. Residual stresses were measured by hole drilling method in critical zones of… Expand
REPAIRING OF PLATFORMING REACTOR BY SAW IN NARROW GAP
Reaktori se nalaze u sklopu reaktorske sekcije, gde se odvija proces platforminga. To je katalitički proces reformiranja nisko kvalitetnog teškog benzina-primarnog benzina u visoko kvalitetno motorno… Expand
WELDED JOINT TENSILE STRENGTH TESTING OF NEW AND USED MATERIAL
The repair process of welded steel construction (tank) requires a number of demanding tests that have to determine whether welded joints fulfill all of the required standards. This paper examines… Expand
AKUSTIČNA EMISIJA – AKTIVNA METODA ISPITIVANJA BEZ RAZARANJA ACOUSTIC EMISSION – AN ACTIVE NON-DESTRUCTIVE TESTING METHOD Pregledni rad / Review paper
Application of acoustic emission in testing materials and structures enables early detection of defects that develop in service that may cause considerable decrease in reliability and operational… Expand
FATIGUE PROPERTIES OF A HIGH-STRENGTH-STEEL WELDED JOINT UTRUJENOSTNE LASTNOSTI ZVARA VISOKOTRDNEGA JEKLA
In addition to the strength and toughness properties, the fatigue properties of welded joints are necessary for the design of high-strength steel structures exposed to variable loading. Wohler curves… Expand
Trends in the Development of Machinery and Associated Technology ” TMT 2010 , Mediterranean Cruise , 11-18 September 2010 TENSILE PROPERTIES OF TWO Al-Mg WELDED PLATES AFTER APPLYING DIFFERENT…
Two Al-Mg alloys: (I) AA5182 type and (II) the same type additionally alloyed with a low amount of Zn and Zr (≈ 0.12%wt each) were processed to 6.5mm thick H116 and H321 marine grade plates. They… Expand
THE EFFECT OF FIBRE ORIENTATION ON FRACTURE PROPERTIES OF GLASS FIBRE- EPOXY COMPOSITE UTICAJ ORIJENTACIJE VLAKNA NA KARAKTERISTIKE LOMA KOMPOZITA TIPA
The effect of glass fibre orientation in an epoxy matrix composite on impact load and fracture toughness is experimentally analysed by testing Charpy V notched specimens, and notched CT specimens.… Expand