Author pages are created from data sourced from our academic publisher partnerships and public sources.
- Publications
- Influence
Experimental Study of Surface Topography Created by Abrasive Waterjet Cutting
- S. Hloch, J. Valíček, I. Samardžić, D. Kozak, J. Müllerová, M. Gombár
- Materials Science
- 2007
In this work has been detailed studied the surface topography of aluminium with the aim of quantification of morphologically different zones initial, smooth, transition and rough zone by means of… Expand
- 40
- 3
Monitoring of focusing tube wear during abrasive waterjet (AWJ) cutting of AISI 309
- Pavol Hreha, A. Radvanská, +7 authors S. Hloch
- Materials Science
- 1 October 2014
The paper deals with the investigating the possibility of using vibrations as a potential source of information for the detection of the malfunctions during the abrasive supplaying and focusing tube… Expand
- 31
- 2
Definition of Terms Relating to Non-Ultimate Mechanical Properties of Polymers
Dokument daje definicije pojmova koji se odnose na mehanicka ponasanja polimernih materijala u podrucju do loma, posebice za masovne polimere i koncentrirane otopine i njihova elasticna i… Expand
- 3
- 1
Integrity assessment of HSLA steel welded joint with mis-matched strength
- N. Gubeljak, J. Predan, I. Rak, D. Kozak
- Materials Science
- 2009
Currently, there is a need to conduct numbers of validation cases for the defect assessment procedure of the recently developed Structural Integrity Assessment Procedure (SINTAP). Current work deals… Expand
- 9
- 1
- PDF
INVESTIGATION OF SANDWICH MATERIAL SURFACE CREATED BY ABRASIVE WATER JET (AWJ) VIA VIBRATION EMISSION
- Pavol Hreha, S. Hloch, +6 authors D. Kozak
- Materials Science
- 2014
The paper presents research a of abrasive waterjet cutting of heterogeneous "sandwich" material with different Young modulus of elasticity of the cutted surface geometry by means of vibration… Expand
- 13
- 1
A New Procedure for the Determination of the Main Technology Parameters of Rolling Mills
- J. Valíček, J. Müllerová, +5 authors M. Harničárová
- Engineering
- 2013
Nowadays, approximately 90–95 % of metals are processed by cold rolling. There has been a substantial increase in demand for utility properties as well as for reducing production costs. These… Expand
MULTIPLE ATTRIBUTE DECISION MAKING TOWARDS MOST ACCEPTABLE VARIANT SOLUTION
- M. Kljajin, Ž. Ivandić, D. Kozak
- Engineering
- 2004
Modern product development concept is based on the product as a technical system. Developed model in this paper connects the product as a technical system and designer. Different models of decision… Expand
- 1
- 1
Review of Potential Use, Benefits and Risks of Nanosensors and Nanotechnologies in Food
- D. Ileš, Goran Martinović, D. Kozak
- Engineering
- 30 April 2011
Usage of nanotechnology in food with all of its possible different applications has potential to significantly change today’s ways of food manufacturing and packaging as well as to alter fundamental… Expand
- 9
- 1
WATER JET TECHNOLOGY USED IN MEDICINE
- Pavol Hreha, S. Hloch, +4 authors M. Rakin
- Engineering
- 30 June 2010
Abrasive water jet technology has been recently used mainly in industrial areas. This technology provides several advantages in comparison with conventional methods. At present, it is used in… Expand
- 27
The influence of heat treatment by annealing on clad plates residual stresses
- B. Mateša, D. Kozak, A. Stoić, I. Samardžić
- Materials Science
- 3 October 2011
The influence of applied clad procedure as well as heat treatment by annealing (650 °C/2h) on level and nature of residual stresses was researched. Three clad procedure are used i.e. hot rolling,… Expand
- 15